MobiFlight Community Support

Hello everyone
I wanted to know the annuciator offset under the hid pumps ( 11 annunciators) and offsets for the servo pressurization, air ,temperature and cabins.
I have find only offset for the gauges fuel temp and Egt Apu.

Unfortunately the other are not present in offset fsupc.

Thank you

Stefano

Sorry my friend..... if you need help you MUST give us all information we need to help you finaly....

I wanted to know the annuciator offset under the hid pumps ( 11 annunciators)

I hope you understand.... I give you offsets if i know it and i will search for it if i not know it directly..... BUT i not look on 30 Fotos of different Aircrafts to find out WHAT you mean here....

Awnser this.
1. WHAT Aircraft Type ? B737, Airbus, MD, Learjet ??
2. WHAT AddOn ? PMDG, Prosim, Standard Aircraft and so on ( Xplane or FSX ??)
3. Tell me the Name of all 11 annaunciators (and the other Stuff you need) so i can search every Offset single.

Basicly.... AddOns not use FSUIPC Offset List..... it got Own lists or allow us to define the offsets ourself in a internal software.
Standardaircrafts use FSUIPC Offsetlist... BUT Lots of Elements are not simulated.... So there exist no Offset for it.

So... Help ME.... Awnser the questions.... And then i try to help YOU !

I'm sorry for the bad information .

1) I have a B 737 overhead
3) I use Fsx
3) I have Pmdg addon

I need the offset for:

FWD ENTRY,FWD SERVICE,LEFT FWD OVERWING,RIGHT FWD OVERWING,FWD CARGO,LEFT AFT OVERWING,RIGHT AFT OVERWING AFT CARGO,AFT ENTRY,AFT SERVICE,EQUIPE.

I'd like the offset servo gauges presurizzation and air temp, air bleed.

Best regards

Stefano

Oh Ok....
Now thats clear !

This offsets was not a part of the basic PMDG 737 and came in a later version ! It was released with Servicepack Patch 1d.

To work with it you need the follow....

1. Get shure your PMDG is on Patch Status 1d DELTA . If not you need to patch it. Patch you got from the puplisher. Maby Aerosoft in Germany or PMDG itself when you buy it in the USA.
2. Your FSUIPC must be up to date ( Or not older then 4.95 i think) ... In that Version Pete Dowson "open" the new offset Range.
3. Like in all other PMDG Stuff you need to enable Data Broadcast by the INI entry ( Explane in the manuals) I pretty shure you already got this when you do other Outputs in the past)

You find the new Stuff in the "Offsetmapping for PMDG737NGX.PDF Document in the /FSX/MODULES/FSUIPCDOCUMENTS Subfolder. NOTE The New offsets are in the updated Version of this document after FSUIPC 4.95 included.

********
Offsets: ( Just copy and paste... For Details look in the lists youreself.... this is all in the last chamber near the end )

Code:

6C14 -1 BYTE DOOR_annunFWD_ENTRY - Boolean
6C15 -1 BYTE DOOR_annunFWD_SERVICE-  Boolean
6C16 -1 BYTE DOOR_annunAIRSTAIR - Boolean
6C17 -1 BYTE DOOR_annunLEFT_FWD_OVERWING - Boolean
6C18 -1 BYTE DOOR_annunRIGHT_FWD_OVERWING - Boolean
6C19 -1 BYTE DOOR_annunFWD_CARGO - Boolean
6C1A -1 BYTE DOOR_annunEQUIP - Boolean
6C1B -1 BYTE DOOR_annunLEFT_AFT_OVERWING - Boolean
6C1C -1  BYTE DOOR_annunRIGHT_AFT_OVERWING - Boolean
6C1D -1 BYTE DOOR_annunAFT_CARGO - Boolean
6C1E -1 BYTE DOOR_annunAFT_ENTRY - Boolean
6C1F -1 BYTE DOOR_annunAFT_SERVICE -  Boolean
*******
6C24 - 4 FLT32 AIR_CabinAltNeedle  - ft
6C28 - 4 FLT32 AIR_CabinDPNeedle  - PSI
6C2C - 4 FLT32 AIR_CabinVSNeedle - Ft/min
6C30 - 4 FLT32 AIR_CabinValveNeedle - 0 closed ... 1 open
6C34 - 4 FLT32 AIR_TemperatureNeedle - Degrees C
6C38 - 8 FLT32 x 2 AIR_DuctPressNeedle 2    / This are 2x 4 BYte FLT32 for both needles !! 

Have Fun !!

Thank's my friend
I' ll try the codes tomorrow.

Best regards

Stefano